How to Remove Flex Seal from Different Surfaces

If you have flex seal on an unwanted area and are looking for a guide on how to remove it, you are on the right page.

Removing this seal from your car, rubber, clothing or metal can be difficult if you don’t know the proper way of going about it.

You can easily scrub for hours without getting anywhere. It doesn’t even matter what kind of chemical you are using. You also need a good procedure and that’s what this article is set out to provide for you.

Since the flex seal is actually a product that seals and joins tightly to the surface it is on, you need another strong material to take it off.

Remember it’s a liquid rubber in a can so you have to do some scrubbing, which requires some time to get through.

Now that you understand what you flex seal is all about, let’s get into the solution of removing the seal from different surfaces.

The strategy required for removing flex seal from different surfaces slightly differ, but all of them can be pulled off by anybody.

Right away let us dive into it:

 

 

How to Remove Flex Seal from Different Surfaces

If you can’t go through each of the steps outlined below, here is a quick video showing you how to remove flex seal. It’s short and to the point:

For those who are ready to read through, here is a detailed guide on how to remove it from different surfaces:

1. Cars

Imagine your little kid spraying your newly bought ride with a flex seal. You’ll probably be mad but obviously can do more than to find a solution.

If you’ve got flex seal on your vehicle, here is what to do:

Get yourself a paint thinner or toluol.

Once you spot the area where the Flex Seal stains your car, apply the thinner in small measurement to the are and strongly rub with a waste cloth. Toluol is an acetone, it will thin the seal and allow you to scrape it off. Make sure the cloth is smooth and doesn’t have sand or similar to not scratch the paint on your car.

2. Metal

You will need a damp cloth and Toluol or any acetone to remove flex seal from a metal surface.

Simply wet the surface and scrub with the cloth continues until the flex seal fades of the surface and leaves no traces of stain. Sometimes, you may have to scrub repeatedly before you can get the stain of your metal.

It’s a common knowledge that when you are removing a strong adhesive, it’ll require some kind of elbow grease. Can’t get it off? Then keep scrubbing. At a point, the flex seal will wipe off and leave your metal surface clean again.

3. Fabric

Fabric requires much of caution when working to remove Flex Seal from them. Not like metals, you should not apply acetone based substances on things like soft-material couches.

Alternatively, apply mineral spirit to emit the Flex Seal from the fabric surface. No need to scrub just scratch out the stain. You can also dry it in a similar one.

Do not try to clean with a dry towel. Blur it again. Fabrics are more fragile and it demands a tender procedure applied to remove any flex seal on them.

Though when the mineral spirit is applied it might not be that of easy or quick as you might think, but it will come off in the long run.

4. Wood

The same applies to wood surfaces. If by mistake spray Flex Seal on a dyed wood, using acetone based substances may not work out.

Apply mineral spirits to come off the Flex Seal from the wood surface effectively. Similar to the metal surface removing flex seal from wood requires some work.

So cleanse the stain to the point where it is no longer. You should rub with a cloth to the point that the surface is perfect.

5. Tile surfaces and concrete walls

Similar to the wood surfaces, acetone may not be the right selection if looking for the best chemical to remove flex seal from tile surfaces and concrete surfaces.

You can also try using a scraper or putty.

If you are scrubbing it off a wall or similarly hard surface, the best option is to use a putty to scrape off the flex seal so that you don’t damage the gouge in your wall.

You can apply alcohol to remove the stain if there is a residue. You have to be careful though, as alcohol may remove the paint on the wall.

A citrus based cleaner would be a better alternative as it doesn’t cause the paint to remove while still removing the stain completely.

 

Concluding Remarks on Removing Flex Seal from Surfaces

Flex seal is an incredible element used to repair or for sealing different materials. However, at any point where a stain is seen or the Flex seal has spread accidentally on surfaces, it can be hurting to see your surface ruined.

It is always preferable to seal the regions or the part that you are repairing to prevent accidental spilling of flex seal to unwanted areas.

So, if you are managing an already ruined surface, the above step by step guide will help you remove the flex seal with little effort. Hope this guide helped you solve your problem. Enjoy the original state of your surfaces.

FAQs on How to Remove Flex Seal from Different Surfaces

Q: Is the flex seal best alternative to sealing the interior parts of an auto?

A: Indeed there are some parts of your car’s interior where flex seal isn’t applicable. For the case, don’t try to apply it on tire tubes and gas tanks

Q: How can I get flex seal off my hand?

A: By soaking your hands in warm water to soften the skin, apply nail polish remover after drying your hands with a towel. Then apply a body lotion to wipe out any softened flex seal. Repeat the procedure to ensure that your hands are totally free of flex seal

Q: What works best to remove unwanted flex seal from surfaces?

A: Of all the available substances that are claimed to have an effect on the flex seal, the mineral spirit is the best alternative. Acetone based chemical may corrode some fabrics and carpet.

Q: Can mineral spirit bleach my fabrics when applied to remove flex seal?

A: Mineral spirit will not bleach your fabrics, when applied in the right measures, in the right amount and only on the affected spots.

1 comment

Leave a Reply

Your email address will not be published. Required fields are marked *